WorkPro PA 120 USB/R Manual de usuario Pagina 7

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 10
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 6
Mains Connection
The supply transformer has been designed for use on either
115Vac or 230 Vac, selected by slide
switch on rear panel. The amplifier is factory set at 230
Vac mains voltage.
Battery Connection (24Vdc)
When using external batteries, earth the amplifier via the screw terminal because of the high
voltages present. Electrical stability of the system is increased by earthing the case.
NOTE: The connection cable must be fitted with an in-line fuse. quick blow type (30W : 5A, 60W :
8A, 120W : 15A, 240W : 20A, 480W : 40A). When Connecting batteries please ensure correct
polarit
y
.
Microphone Connection
Mic1~4 inputs are balanced standard 1/4” stereo jack, DIN and XLR Socket on the rear panel
(With selectable phantom power). Wiring is as follows:
XLR (Balanced Operation)
Pin1 : Screen
Pin2 : Signal (live)
Pin3 : Signal (return)
DIN (Balanced operation)
Pin1 : Signal (live)
Pin2 :
GND
Pin3 : Signal (Return)
Pin4 : Priority Control
Pin5 :
GND
1/4” Stereo Jack Plug (Balanced operation)
Tip : Signal (live)
Ring : Signal (Return)
Sleeve : Screen
Priority Microphone
Mic1 input has VOX priority which will override Mic2~4 and Line input signals but NOT the
TE
L / EMER input.
Mic2 input which will override Mic3~4 and Line input signals but NOT the TEL/EMER and Mic1
Inputs.
Mic3 input which will override Mic4 and Line input Signals but NOT the TEL/EMER Mic1 and
Mic2 Inputs.
Mic4 input which will override Line input Signals only but NOT the TEL/EMER Mic1, Mic2, and
Mic3 Inputs.
Mic3~4 input are (DIN, phone / XLR) with Selectable phantom power located on the rear panel
and wire as above. Mic1~2 input are with Selectable phantom power located on the PCB
(sw401, sw402)
1
4
2
5
3
2 1
3
CONTROL
SYSTEM
PRIORITY
CHIME SIGNAL
+VCC
CD
AUX
MIC4
MIC3
Pre AMP
BUS
MUTE
Pre AMP
Pre AMP
MUTE
MUTE
+VCC
+VCC
+VCC
MIC1
MIC2
+12V
(50mA)
VOX
Pre AMP
Pre AMP
MUTE
MUTE
SW
CHIME ON/OFF
Pre OUT
Pre AMP
VOX
RECTIFIER
FUSE
MOH DRIVER
8OHM
COM
100V
TRANS.
FUSE
PA120/2 PRO
TEL
115V/230V
600OHM
8OHM
COM
DC24V
POWER IN
VCA
RELAY
LINK
Pre AMP
Pre ANP
LINE OUT
CONTROL
VOLUME
MASTER
CONTROL
COM 8 100V COM 100V
DC 24V
PRE OUT
MIC 2 MIC 1
SENS VR
MONITOR OUTPUT TEL/EMER
SENS VR
MIC 4 MIC 3
MUSIC/SPEECH
LINE FUSE
Connected for 230v~
Apparatus delivered
115V~
230V~
600 1V
8
1W ~ 0 ~+ P
MICMIC LINELINE
PHANTOM
PHANTOM
+
GND
GND
MAX 6W X 20
PA 120 USB/R User Manual/Manual de uso Pag 12
PA 120 USB/R User Manual/Manual de uso Pag 5
Vista de pagina 6
1 2 3 4 5 6 7 8 9 10

Comentarios a estos manuales

Sin comentarios